DON'T KNOW YOUR ACTUAL SHOCK AND VIBRATION LEVELS?
We measure them for you.
Fill in the request form
or read how Field Measurement works
Measured data instead of assumptions
Before designing any damping solution, you need to know what you're actually dealing with. Without accurate data, every decision is based on assumptions, which will lead to systems that are over-engineered, underspecified, or don't match the environment.
Field Measurement & Data Logging remove uncertainty by recording real shock and vibration levels.
✓ Real-world data recorded on-site
✓ Converted into SRS curves and load cases
✓ Validated input for compliance and certification
Field Measurement & Data Logging is used for:
- Military vehicles and naval platforms
- Offshore structures
- Industrial machinery
- Transport and logistics environments
✓ No more guesswork
Real operational loads are recorded, not assumed, removing uncertainty from the design process.
✓ Accurate engineering input
Measured data feeds directly into SRS curves and our Calculation & Simulation Software.
✓ Compliance-ready documentation
Verified input data supports your certification and procurement process.
✓ Confidence in existing systems
Confirms whether your current damping solution is still performing as intended.
Equipment used in the field
Our Field Measurement & Data Logging service uses standalone, self-powered data loggers selected per application, mounting position, and required accuracy. The selection below is drawn from our full equipment range for project-specific requirements, feel free to contact us.
KQV2.5 20-02
KQV2 .5 20 - 02
JV1.5 1-10
JV1.5 1 - 10
JV1.5 15-10
JV1.5 15 - 10
JV1.5 5-10
JV1.5 5 - 10
JV1.5 3 - 10
JV1.5 3 - 10
All our products are manufactured and tested in Europe.
"Not knowing your real-world loads isn't a dead end. It's where every accurate damping solution begins."
Field Measurement & Data Logging is used in:
Field Measurement & Data Logging (FMD)
For real-world shock and vibration data collection.
When operational data is unavailable or uncertain, we perform on-site measurements using standalone data loggers. Shock and vibration levels are recorded directly in the field to provide accurate input for system design and verification.
✓ Real operational loads are unknown
✓ Existing systems show unexpected vibration behaviour
✓ Verification testing is required
✓ Reliable input data is critical for compliance
- Military vehicles and naval platforms
- Offshore structures
- Industrial machinery
- Transport and logistics environments
Calculation & Simulation Software (CSS)
For precise, validated dimensioning of your damping system.
Our in-house software analyses and dimensions spring and damper systems under severe shock and vibration loads, using either measured field data or project specifications as input. Dynamic behaviour is evaluated in both time and frequency domains.
[Learn more about Calculation & Simulation]
Field Measurement provides the real-world data; CSS turns that data into a validated, certifiable design.
✓ Compliance with MIL, AECTP, DEF STAN, or naval standards is required
✓ Shock Response Spectra (SRS) evaluation is needed
✓ Controlled stresses and displacements must be verified
✓ Certification support is required
- MIL-STD-810 / MIL-STD-167
- MIL-STD-901
- AECTP-400
- DEF STAN 00-035
- BV 0430 / BR 8470
TURN MEASURED DATA INTO CERTIFIED ENGINEERING INPUT
At Damping Solutions, Field Measurement data is not just some numbers; it becomes documented, traceable engineering input. Recorded shock and vibration levels are converted into SRS curves and load cases, verified against international standards, and made available for your certification or procurement process.
✓ MIL-STD-810 / MIL-STD-167
✓ MIL-STD-901
✓ AECTP-400
✓ DEF STAN 00-035
✓ BV 0430 / BR 8470
How does Field Measurement work?
- Deploy: Standalone data loggers are installed directly at the relevant measurement point.
- Record: Shock and vibration levels are logged under real operational or transport conditions.
- Convert: Recorded data is processed into SRS curves and load cases.
- Engineer: Results feed directly into our Calculation & Simulation Software for validated system design.
Frequently asked questions about Field Measurement
On-site recording of real shock and vibration levels using standalone data loggers, used as accurate input for damping system design.
This depends on the application from a single transport leg to continuous monitoring over several weeks, depending on what needs to be captured.
Standalone, self-powered data loggers such as the Saver 3D15 and Saver 9X, selected based on required accuracy, duration, and mounting conditions.
Recorded data is converted into SRS curves and load cases, which are used directly in our Calculation & Simulation Software to dimension the correct damping solution.
Yes. Measured field data can be used to define realistic test profiles for our ISO/IEC 17025-accredited Testing & Validation service.
ALREADY KNOW YOUR LOAD AND VIBRATION DATA?
If your operational shock and vibration levels are already known, explore our Wire Rope Mount range engineered for the exact conditions you've measured, with no fluids, no rubber, and no consumable parts.
Ready to measure real-world conditions?
Start with a free calculation
Our engineers perform a first calculation free of charge.
Send us your load and frequency data, and we'll recommend the right isolation concept with full documentation for your engineering or procurement process.